DA1468x

Create multiple characteristics in a single BLE Service?

Mon, 2019-09-09 18:54--mahmed106

嗨对话框

I want to create multiple characteristics in a single service, right now i am working on pxp reporter and added my custom service from the dialog website tutorial. Its working great, but now i want to add more characteristics but cannot find an example code or tutorial.

谢谢

In custom board VBUS is NC, is there any other way to wakeup form hibernation.

Fri,2019-08-16 08:40--mahmed106

嗨对话框

We designed out custom board and now we are desiging our firmware to prevent battery discharge too much when board not in use.

所以我们正在使用DG_CONFIGBattery_LOW_LEVEL宏将其设置为休眠模式。

But in custom board VBUS is NC, is there any other way to wakeup form hibernation?

:/DA1468x_DA15xxx_SDK_1.0.14.1081/sdk/bsp/startup/startup_ARMCM0.S:38:2: error: #warning "Building Production image with MAGIC V

Wed, 2019-05-15 11:26--mahmed106

I am building my project but i am getting this error. I can't understand the meaning of this. Can someone explain it to me what i did wrong.

:/DA1468x_DA15xxx_SDK_1.0.14.1081/sdk/bsp/startup/startup_ARMCM0.S:38:2: error: #warning "Building Production image with MAGIC Value check enabled! Possible security risk..." [-Werror=cpp]
#warning "Building Production image with MAGIC Value check enabled! Possible security risk..."
^
cc1.exe: all warnings being treated as errors
制作:*** [startup / startup_armcm0.o]错误1

Device sacn

太阳,2019-01-27 16:32--拉贾山

Dialog team,

My question is how we can scan ble device in pxp_reporter example code.
I am familiar with hrp_collector and and hrp_collector example. I know the "ble_gap_scan_start" API call and "handle_evt_gap_adv_report" handler. I tried this api in pcp_reporter but as soon as I call "ble_gap_scan_start" immediately "handle_evt_gap_adv_report" called.
So, kindly help me how we can scan ble devices in peripheral (pxp_reporter example) code?

谢谢
raj.

DA14683燃油计

星期一,2018-09-03 17:42--bobspam@free.fr

Hello

我希望通过外部驱动的N沟道MOSFET更换用于测量DA1468x的功耗的0.1欧姆电阻。
For instance DMN6140 has a 0.14 Ohm internal resistance.

- Does the fuel gauge can support a N-Channel MOSFET instead of the 0.1 Ohm resistor (0.14 Ohm) ?
- Does the fuel gauge support the "switched-off state" (considering that the mosfet will cut power of vbat)

Thank you in advance

DA1468X低功耗模式

Wed, 2018-08-22 20:16--Jitendraprasad

你好对话小组

I am working on pxp_reporter example and write application for some sensors and put the device in extended sleep mode. When device enter in sleep mode after 8 seconds device consume low power. Device wakeup on timer interrupt and read sensors data and record in flash. So, when timer trigger device wakeup but it get stuck somewhere.
After debugging I came to know the SPI handle (SPI open) value get changed in wakeup mode also changed variable values etc. I have enabled RAM RETANTION and configure GPIO in priph_int function in main.c file.

Problem with da1468x UART pin connection

Sun, 2018-07-08 10:26--Anonymous (not verified)

Hello Dialog,
I have a da14681 development kit basic board and i have programmed PXP_Reporter demo code into board. when i connect UART RX pin (P2_3) to TX pin of USB2Serial Module, the BLE part of the code crashes in 8 seconds after the reset. i disabled the sleep mode with this code (pm_set_sleep_mode(pm_mode_active);) and also disconnected the j13 jumpers but there was no any changes. do you know what is the problem?
谢谢 ...

Pages

订阅RSS - DA1468x