Hallo,
I am using SDK 5.0.3 and implemented the custs1 profile into my custom project. When I connect to the device I see the correct UUID of the profile and all the services.
My question now is where to implement the callback functions for receiving and transmitting data?
你好, 我是學習使用da14580寫BLE的新手, 本身也沒寫藍牙的經驗.
在使用SDK5.0.3 按照tut (Training_01_advertising_contents_v1.0) 的步驟修改ble_app_barebone 後 使用bluetooth Le scanner 卻找不到Diaglog-Training 的裝置
而 smartsnippets 在燒入的過程也是全successfully的 所以想請問發生了甚麼事?
Hi
I want to interface an external EEPROM with the daughter board available with my pro kit. Where can I get the board schematic for the same?
Thanks in advance
Hi Dialog Team,
I have been using DA14583 daughter board on DA14580 pro mother board. And the board is working fine. But when I am replacing DA14583 daughter board with DA14580 daughter board, the system is not working. I have been using the ble_barebone project. The system execution begins, but no packets are emitted through DA14580 board. Is there any modification required for configuration of type of board(DA14583 or DA14580) . Also, I have been using BASIC DA14580 development kit, and even this is not working fine. No packets are getting transmitted in either case.
Hi Dialog team
I am currently using your product embedded in Murata type ZY in Mass production product.
I would like to the SKY1111-11 range extender, and currently trying to evaluate this. I have two questions:
1. Does the evaluation kit can be purchased? if can , where can i buy one.
2. There is a connection of TX_EN to V_BIAS through a 3.3Kohm resistor, and there is some explanation about it (so the current will not exceed 16.5mA )- there is something behind it , or I connect the TX_EN and Bias voltage through a 0 ohm.
thanks
有一个项目是MCU+DA14580的架构, 想不使用SPI flash 和OPT , 每次启动都由MCU 通过Uart下载code到DA14580中运行.
DA14580 工作于 DSPS5 device .
请问, 如果每次code都下载在RAM中运行, EXT sleep mode 和 WDT RESET 功能受不受影响?
谢谢!
Hi,
We have built our prototype boarsd of our product, which uses PAN1740. Initial testing was successful with the full functionality of the product until the SUOTA is carried out.
The SUOTA was complted and the reboot command was sent. But the device did not reboot. After careful testing we found out that Gnd and Vcc of the PAN1740 were showing short.
We had 1uF and 0.1uF decoupling capacitors. What is the reason for this?
All the design is in reference with the dialog semiconductor application notes and user manuals.
请帮忙审核下我的账户,点击了审核,但是后面没有收到消息
刚接触蓝牙应用,想跟着官方的引导文档在我们的产品蓝牙服务中添加几个Characteristic,但是现在的账户没有权限看到这些文档
谢谢
Hi,
I'm following the guide Tutorial 5 : configuring sleep mode on DA1458x.
When I do my messurement as they do in the tutorial I get 2,4 uA instant current and around 3,2 uA as average current.
I use basic development board 14580.
What SDK is used in the tutorial?
Is there some more parameter that has to be set?
Best regards
Viktor
Hi Dialog Support,
After looking data sheet, 4.7.2 wake-up timer, it looks like wake up timer only works after pre-defined number of GPIO event, can I understand that external wake up method is the only way to wake up 14580 after falling into extended or deep sleep (by configuration in user_config.h?
