Failure to Burn and load from SPI Flash

Learn MoreFAQsTutorials

6 posts / 0 new
Last post
Sat, 2020-05-23 12:59
#1
Roie DAHAN
Offline
Last seen:3 months 3 weeks ago
Joined:2018-11-19 16:32
Failure to Burn and load from SPI Flash

Dear Dialog Support Team,

I would like to get your advise about how to burn the SPI flash on Pro developement Kit (DA14585)

Since somehow the SPI is not burned and obviosly software can run from it after RESET

I Followed these steps:

  • Complie using Keil peripheral_examples\blinky
  • open SmartSnippets Toolbox v5.0.12.2786
  • Open Board Setup tab and set:
    - SPI_CLK: P0_0
    - SPI_EN: P0_3
    - SPI_DI: P0_5
    - SPI_DO: P0_6
  • Open SPI Flash/EEPROM tab
  • Press on Load hex/bin file and selected peripheral_examples\blinky\Keil_5\out_DA14585\Objects\blinky_585.hex
  • Press on Connect button
  • Press on Read 32KB
  • Read Result All 0xFF (as it should be clean Flash)
  • Press on Burn & Verify button --> all pass okay (attached print screen and log file)
  • Press on Read 32KB All 0xFF still having a clear Flash

Please advise what step(s) i'm missing?

*Note:

1). Attached Board picture with Jummper settings

2). Print Screen of SmartSnippets Toolbox v5.0.12.2786 after these steps

3). log file

Thanks,

Roie

Attachment:
PDF iconSPI Flash.pdf
Device:
DA14585
Mon, 2020-05-25 11:08
PM_Dialog
Offline
Last seen:15 hours 42 min ago
Staff
Joined:2018-02-08 11:03
Hi Roie DAHAN,

Hi Roie DAHAN,

Could you please share screenshots from the SS Toolbox when you pressed the following buttons:

  • Connect
  • Read 32K
  • Erase
  • Burn & Verify

If it is possible, I’d like to see the “Log” window in the screenshots (like the attached screenshots)

In the jumper’s setup, it’s not clear if you placed the jumpers in the SPI position, so I assume that are correctly placed.

After burning the SPI Flash, please press “Connect” and then try to read it..

Thanks, PM_Dialog

Mon, 2020-05-25 11:32
Roie DAHAN
Offline
Last seen:3 months 3 weeks ago
Joined:2018-11-19 16:32
Hi Support Team,

Hi Support Team,

I Found the Error --> close and re-open SS Toolbox resolved the issue

Thanks for the prompt reply

Roie

Accepted answer
Mon, 2020-07-13 00:43
(Reply to #3)
Luis_magadan
Offline
Last seen:4 months 12 hours ago
Joined:2020-01-08 20:16
Hello, I have problems too

Hello, I have problems too while programming the Smartbond DA14585 Multisensor using Dialog smartsnippets Toolbox. Could you explain me how do you do this correctly? After I burn the firmware the logger said that all is correct but the sensor never starts blinking.

你跟着做什么措施都正确吗?

Thanks.

Mon, 2020-05-25 11:53
PM_Dialog
Offline
Last seen:15 hours 42 min ago
Staff
Joined:2018-02-08 11:03
Hi Roie DAHAN,

Hi Roie DAHAN,

Glad that you figured your issue out.

Thanks, PM_Dialog

Mon, 2020-07-13 14:16
PM_Dialog
Offline
Last seen:15 hours 42 min ago
Staff
Joined:2018-02-08 11:03
Hi luis_magadan,

Hi luis_magadan,

Please refere to the user guide and you will find detailed steps :

http://lpccs-docs.dialog-semiconductor.com/UM-B-083/index.html

Thanks, PM_Dialog