⚠️
Hi there.. thanks for coming to the forums. Exciting news! we’re now in the process of moving to our new forum platform that will offer better functionality and is contained within the main Dialog website. All posts and accounts have been migrated. We’re now accepting traffic on the new forum only - please POST any new threads at//www.xmece.com/support. We’ll be fixing bugs / optimising the searching and tagging over the coming days.
4 posts / 0 new
Last post
bobspam@free.fr
Offline
Last seen:2 months 1 week ago
加入:2018-06-20 08:07
DA1468x - External Battery Charger (1A)

Hello

The battery charger provided by the DA1468x is too slow for my application and I would like to check with you if I can use an external charger while keeping the USB features of the DA1468x.

- Main idea is to use MCP73830 1A that uses 2 GPIOs : enable / status

- This would imply to use the dg_configUSE_USB_CHARGER (0) flag to avoid enabling internal charger and to manually drive gpios to allow enabling the charger

I could figure out that when using dg_configUSE_USB_CHARGER the only callbacks that are called are "usb attached" and "usb enum"

Can you confirm to me that power is available from charger when usb_start_enumeration_cb() is called ?

Are there any way to know the maximum available power after enumeration so I can check I can get 1A from the charger ?

Thank you in advance

Best Regards

Device:
PM_Dialog
Offline
Last seen:21 hours 6 min ago
工作人员
加入:2018-02-08 11:03
嗨,鲍勃,

嗨,鲍勃,

DA14680 contains a dedicated on-chip charger which allows the chip to natively charge rechargeable batteries over USB. The charger is up to 5.0 V with programmable curves. Please read the 4.1.6 Charger section in the datasheet. There is a dedicated Pre-Charge and Charge SW FSM. If you would like to add changing functionality, you should follow the AN-B-035 document (link is provided below). You should follow standard procedure and the changing should be done over USB.

//www.xmece.com/sites/default/files/an-b-035_da1468x_battery_charging_1v1.pdf

Thanks, PM_Dialog

bobspam@free.fr
Offline
Last seen:2 months 1 week ago
加入:2018-06-20 08:07
Hello

Hello

Thank you for the application note.

I am targetting an application requiring 7Ah of battery capacity and 6 weeks of autonomy. I am out of spec of the internal battery charger (max 500mAh) so I do need to add an external one. For cost reasons I still wish to use the USB features provided by the DA1468x thus the dg_configUSE_USB_CHARGER (0) match my needs.

我可以测试工程师t it with a set of usb chargers and I coud figure out that most of the time the state machine stays in USB_CHARGER_CONNECT_PENDING state after enumeration ( usb_start_enumeration_cb() is called before that state is reached so I can not use that hook ). I tried to plug the device on samsung chargers, chinese chargers and the result is the same. I tried to plug it on a usb hub and the state machine stays stuck in USB_CHARGER_ATTACHED which means that the hub does not provide charging capacity.

Can you confirm to me that I can rely on this state to manually drive an external battery charger using the following ? I am not sure the USB negotiation is being achieved properly.

if (usb_charger_state >= USB_CHARGER_SDP && usb_charger_state < USB_CHARGER_PAUSED) {

// activate external battery charger

}

Thank you

PM_Dialog
Offline
Last seen:21 hours 6 min ago
工作人员
加入:2018-02-08 11:03
嗨,鲍勃,

嗨,鲍勃,

As I mentioned in my previous reply, the procedure you should follow in order to add changing functionality is described in the application note. Where did you find this if-statement? I would suggest you to modify SDK files. The SDK should be used as it is provided.

Thanks, PM_Dialog