IoT Sensor: default configuration in FW | Dialog Semiconductor customer support - 亚博全网,亚博电竞菠菜,亚博国际官网平台网址

8 posts / 0 new

Last post

星期一,2019-05-20 13:16

gme_johannes

Offline

Last seen:2 weeks 3 days ago

加入:2017-12-22 10:09

IoT Sensor: default configuration in FW

Hi Dialog support,

I am running a project based on the IoT sensor with SDK 5.160.1.19.

When I connect with the IoT app, the default settings are (e.g.)
- SF rate: 10Hz
- Calibration Mode: Continuous Auto
- Auto Calibration Mode: Basic

I want to change the FW before compilation such that the default is
- SF rate: 25Hz
- Calibration Mode: Continuous Auto
- Auto Calibration Mode: Smart Fusion

I have changed the following line in user_sensor_config.c :

const sensor_config_struct sensor_config_default = { ENABLE_ALL_SENSOR_FLAGS, DEFAULT_BMI160_ACCEL_RANGE, DEFAULT_ACCEL_DATA_RATE, DEFAULT_BMI160_GYRO_RANGE, DEFAULT_GYRO_DATA_RATE, DEFAULT_MAG_DATA_RATE, DEFAULT_ENV_SAMPLE_INTV_MULT, DEFAULT_SFL_RATE_HZ, 1, CAL_SMARTFUSION_AUTOCAL, 0, 0, 0, 0, 0, 0 };

Still when I connect the IoT Sensors app, it shows the "old" default setting. This is inconvenient as the basic calibration never works (sensor always drifts - magnetometer?).

How can I change this behavior?

Best regards

Johannes

Device:

DA14580

Mon, 2019-05-20 16:47

PM_Dialog

Offline

Last seen:2 days 2 hours ago

加入:2018-02-08 11:03

嗨gme_johannes,

Did you try to change the default values in the user_app_wrbl_config.h file? The default values in the sensor_config_default structure are defined in user_app_wrbl_config.h.

Thanks, PM_Dialog

Mon, 2019-05-20 16:54

gme_johannes

Offline

Last seen:2 weeks 3 days ago

加入:2017-12-22 10:09

Hi PM_Dialog,

in this document I found

#define DEFAULT_SFL_RATE_HZ 10

which I changed to

#define DEFAULT_SFL_RATE_HZ 25

but I found nothing about the default calibration method.

Now I changed the struct from

const sensor_config_struct sensor_config_default = { ENABLE_ALL_SENSOR_FLAGS, DEFAULT_BMI160_ACCEL_RANGE, DEFAULT_ACCEL_DATA_RATE, DEFAULT_BMI160_GYRO_RANGE, DEFAULT_GYRO_DATA_RATE, DEFAULT_MAG_DATA_RATE, DEFAULT_ENV_SAMPLE_INTV_MULT, DEFAULT_SFL_RATE_HZ, 1, CAL_BASIC_AUTOCAL, 0, 0, 0, 0, 0, 0 };

const sensor_config_struct sensor_config_default = { ENABLE_ALL_SENSOR_FLAGS, DEFAULT_BMI160_ACCEL_RANGE, DEFAULT_ACCEL_DATA_RATE, DEFAULT_BMI160_GYRO_RANGE, DEFAULT_GYRO_DATA_RATE, DEFAULT_MAG_DATA_RATE, DEFAULT_ENV_SAMPLE_INTV_MULT, DEFAULT_SFL_RATE_HZ, 1, CAL_SMARTFUSION_AUTOCAL, 0, 0, 0, 0, 0, 0 };

should this suffice to have the fusion autocalibration at bootup?

edit:
I have recompile and reprogrammed, still the IoT Sensors app shows 10Hz and "Continuous Auto".
Same if I press "Read configuration from NV".

解决这个问题的正确方法是什么？

Thanks,

Johannes

Wed, 2019-05-22 17:49

PM_Dialog

Offline

Last seen:2 days 2 hours ago

加入:2018-02-08 11:03

嗨gme_johannes,,

Could you please try to undefine the USE_SPI_FLASH_CONFIG macro in user_app_wrbl_config.h file?

Thanks, PM_Dialog

Fri, 2019-06-14 12:48

(Reply to #4) #5

gme_johannes

Offline

Last seen:2 weeks 3 days ago

加入:2017-12-22 10:09

Hi PM_Dialog,

(1) can you explain what happens when USE_SPI_FLASH_CONFIG is defined/undefined?

(2) Where do the default values come from in each case, when it is defined and when it is not?

(3) How are the values stored when I changed the configuration from the app and then "write to NV memory"? Does this still work when USE_SPI_FLASH_CONFIG is undefined?
edit: I have found out that "write to NV memory" does not have any effect with USE_SPI_FLASH_CONFIG undefined. It makes sense.

(4) Although in the code I have set

const sensor_config_struct sensor_config_default = { ENABLE_ALL_SENSOR_FLAGS, DEFAULT_BMI160_ACCEL_RANGE, DEFAULT_ACCEL_DATA_RATE, DEFAULT_BMI160_GYRO_RANGE, DEFAULT_GYRO_DATA_RATE, DEFAULT_MAG_DATA_RATE, DEFAULT_ENV_SAMPLE_INTV_MULT, DEFAULT_SFL_RATE_HZ, 1, CAL_SMARTFUSION_AUTOCAL, 0, 0, 0, 0, 0, 0 };

with CAL_SMARTFUSION_AUTOCAL, the IoT app shows "Basic Autocalibration" instead of "Smart Fusion Autocalibration". Can you confirm? How can I boot up with the latter?

BR Johannes

Thu, 2019-06-20 15:40

PM_Dialog

Offline

Last seen:2 days 2 hours ago

加入:2018-02-08 11:03

嗨gme_johannes,

If you undefine the USE_SPI_FLASH_CONFIG you could load data from the default array and in the user_app_wrbl_config.h change the SENSOR_SAMPLE_RATE_IMU to a user sample case, for example SENSOR_SAMPLE_RATE_USER_CASE2 and choose for that sample case BMI160_ACCEL_OUTPUT_DATA_RATE_200HZ and BMI160_ACCEL_OUTPUT_DATA_RATE_200HZ. Regarding the default values in the IoT app, as you correctly mentioned you should modify the sensor_config_default. After recompiling the code, the values should be changed. In addition, you could change the calibration mode inside the app and press the “store” button.

Thanks, PM_Dialog

Mon, 2019-06-24 10:36

gme_johannes

Offline

Last seen:2 weeks 3 days ago

加入:2017-12-22 10:09

Hi PM_Dialog, thanks for your

Hi PM_Dialog, thanks for your answer.

不幸的是，我仍然不能被人注意到我的观点（4），虽然我将默认值设置为“cal_smartfusion_autocal”，但该应用程序仍然显示基本校准。我现在手动改变了所有传感器并用应用程序将其存储到NVRAM。

BR Johannes

Thu, 2019-06-27 15:33

PM_Dialog

Offline

Last seen:2 days 2 hours ago

加入:2018-02-08 11:03

嗨gme_johannes.

Thanks for your indication and for your feedback

Regards, PM_Dialog