Hi Dialog,
I am following the procedure in the AN-B-007 (DA1458x Bluetooth Direct Test Mode) document, to perform the DA14585 to TEST mode,
This procedure need the tool "Connection Manager ",
But I cannot find this tool in the Dialog website,
Could you please tell me where can download this tool?
谢谢！！
Device:
Hi yeh928,
I suppose that you have the latest Smart Snippets Toolbox, one of the options that you have in the Tools section is the RF Master, with that tool you will be able to perform the RF testing of the device. The Connection Manager Tool was an older version of that tool for the 580 in a seperate software version.
Thanks MT_dialog
Hi Dialog,
Thanks for your reply,
After browsing the documents page of DA14585, only have the "AN-B-007 DA1458x Bluetooth Direct Test Mode V1.2 (02/04/2017)" can be found!
But, this document only can find using the "Connect manager" test proceeded, not an "RF Master"!
Has any other document used the "RF Master" to perform the DTM Mode on the DA14585?
We need to perform the RF PHY test use DA14585,
Thanks!
Hi yeh928,
The Connection Manager software, that is used in order to perform the tests, is replaced by the RF master in the Smart Snippets toolbox, the options that you have between those tools are identical, also you will be able to find information of RF Master Tool in the User Manual of Smart Snippets Toolbox (check the Help menu in the SST). Please follow the steps below in order to perform the tests:
Thanks MT_dialog
Hi Dialog,
我使用RF Master并从SDK6.0.4封装下载到DA14580DEVKT + DA14585（以下称为DA14585 DEV板）（路径：DA14585_SDK \ 6.0.4.326 \ Binaries \ DA14585 \ Prod_test）下载“prod_test_585.hex”
After hex file Download successfully, Some command can be sent to DA14585 dev board
(EX: LE Tx/Rx, Reset) and can watch some log list in the log window.
(Please refer the "rf-master log" in the attached file)
But, I need to send the "HCI Command" and get "HCI Event" directly to the DA14585 dev board (EX: Reset Command=> 01 03 0C 00).
I tried sending the HCI Command by using the serial application "Serial Port Utility" to connect the COM Port directly on the DA14585 dev board. (In the System, it detects the two COM Port, use the baud rate 115200 to connect), I tried any one, but DA14585 dev board is response such as abnormal. (not standard HCI event)
(Please refer the "send_response.txt" in the attached file)
Could you please help me how to send the HCI command directly via serial port(COM Port) on the dev board?
Thanks!
Hi Dialog,
I tried the both version of SDK (6.0.4.326 and 6.0.2.243) via "RF Master"
(Download the prod_test_585.hex and try some HCI Commands)
The HCI event is no response or responds incorrectly in current version(ver 6.0.4.326) after send the HCI Command in the "RF Master" or send the HCI to serial port directly vi "Serial Port Utility".
(Please refer the attach file da14585_log_compare.zip)
Could you please help me to fix this problem?
(I need to perform the 2M signal on the DA14585, but old SDK version is not support 2M signal.)
Thanks!
Hi yeh928,
The prod_test tool doesn't support all the HCI commands that are available on the BLE spec but certain commands used by the "RF Master" tool in order to perform some basic testing, in order to use the HCI commands please download the hci project in the 585 \DA14585_SDK\6.0.4.326\projects\target_apps\hci\hci, also please use the flow control lines. Also i dont understand what you mean "I need to perform 2M signal".
Thanks MT_dialog
Hi Dialog,
I know the prod test tool is not support all of the HCI Command and only available on the BLE spec,
But the "HCI_RESET" HCI Command must support all of the bluetooth device define in the bluetooth Core Spec 5.0
（请参阅蓝牙规范版本5.0 | Vol 2，Part E，第7.3.2节重置命令，第904页）
The RF master has "Reset" Button can send the HCI_Reset Command to DA14585 DEV Board.
I verify the two version of SDK, The prod_test_585.hex in the current version(6.0.4.326) SDK may not work properly.
In the Previous version(6.0.2.243) of SDK, It CAN WORK PROPERLY,
(Please refer the screen capture in attach file of two version. "Rf-master_Reset.zip")
In this version of SDK(6.0.4.326), it CANNOT respond properly of HCI event.
Could you please help me to check this version(6.0.4.326) of "prod test tool" has any problem?
Or, Just the "prod_test_585.hex" at version(6.0.4.326) in package is damage?
Could you please provide a normally "prod_test_585.hex" to me?
Thanks!
Hi yeh928,
Ok, now i got it, missed your comments on the previous attachement that you were trying with a different SDK. So, the 6.0.4 SDK is only for the new 585 silicon and none of the examples can properly execute on an older 585 silicon, thats why you dont get the proper response on the HCI commands with the new SDK.
Thanks MT_dialog
Hi Dialog,
According to the Dialog website,
如果我不能找到一个新的585licon publish on the website
I had bought this DA14585 Dev board last week.
== < Please refer DA14585 PCB as capture as attach file. > ==
The printed word on the chip is (DA14585 AB000 1703NCAB)
Label on the back side of the board (DA14585-01ATDB-P 1711_00076)
Could you please help me to check this DA14585 is new or older 585 silicon,
If this is an older, Please help to how to get a new version 585 silicon.
Or, If this is a current version.
Please provide a normally "prod_test_585.hex" to me?
Thanks
Hi yeh928,
Yes, its an older silicon, the SoC indicates the version of the chip as AB and that is an older silicon, it should indicate AC or 00 in versions that run with the 6.0.4. Now normally you should not have this kind of SoC version, so did you purcahse that daugherboard or an FAE provided that (if an FAE provided that, you should come in contact with him in order to change that daughter board) ? At the moment all the daughter boards at the market should be the updated version.
Thanks MT_dialog
Hi Dialog,
Due to us having re-work the DA14585 daughter board
(We had added the SMA Connector on the board)
And, I bought this DA14585 Development Kit-Pro (DA14585-00ATDEVKT-P) from Mouser via oversea shipping.
Now, I had a motherboard, and DA14585 daughter board with older silicon,
So, We plan to reorder DA14585 daughter board Only (New Silicon),
Could you please help me check the following items:
1. How do check the DA14585 daughter board has on-board the "New silicon or not" listed on the online store?
2. Where to buy the DA14585 daughter board (new silicon) Only on the online store? A what is the model name?
(The Dialog only provides the "DA14585 Development Kit-Pro" link)
3. Every version of the SDK update, The old version devices(older silicon, "in this case") is always dropped?
I very worried after ordering a new DA14585 daughter board, the next version of SDK has dropped this version silicon.
Thanks for your support and reply!
hi Yeh928, we will arrange for a swap-out for a new daughter card for you, free of charge. We can confirm that final production version Silicon (now fully released) had a minor metal change compared to the version on this daugther card you have. I will have someone from local Dialog team in Taiwan reach out and arrange this with you. BR JE_DIalog
Hi Dialog,
Will I need prepare the some contact info to the Dialog Taiwan?
What do I have to do next?
Thank you for your help.
Hi Dialog,
So far, I have not received any information from the Dialog Taiwan team,
Could you please help me to check?
Thanks!
Hi yeh928,
Just pinged them, let me know if they contact you in the following days.
Thanks MT_dialog
Hi Dialog
I received DA14585 BOARD from another company.
Which JTAG TOOL should be used for SOFTWARE UPDATE operations?
Thank you for your response
Hi moonjg,
请不要发布问题无关的线程,you can always create a new thread to post your question.
Regarding your issue i dont quite get the question, what exactly do you mean ? The JTAG that Dialog uses and recommends is the ARM Jlink Lite, if you have a dev kit then the JTAG is attached on the development kit.
Thanks MT_dialog