Learn MoreFAQsTutorials

14 posts / 0 new
Last post
Fri, 2017-10-06 09:59
#1
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
RF testing for DA 14585

Hi,

We need to perform RF testing on the DA 14585 chipset. I was trying to use the RF master in the smart snippets toolbox for the same, but was not able to produce any results. The basic requirement is to send unmodulated carrier waves in the 3 different frequencies corresponding to channel 37,38 and 39 and to verify the power and frequency of the output wave using spectrum analyser. Please suggest the possible way to do this.

Thanks and regards
Wisilica

Device:
DA14585
Fri, 2017-10-06 12:47
STS_Dialog
Offline
Last seen:3 years 2 months ago
Joined:2017-06-06 09:26
Hi wisilica,

Hi wisilica,

It's better to use the SDK 6.0.4.326 version the RF master should be work. Please use this sdk and the bellow configuration. At Rf Master at the latest Firmware select this path \sdk_6_practice\DA14585_SDK\6.0.4.326\binaries\da14585\prod_test\prod_test_585.hex. Then from unmodulated Tx/Rx mode choose the Tx , it will be ok for you, check and this please.

https://support.dialog-semiconductor.com/forum/search?term_node_tid_dept...

BR,

STS_Dialog.

Mon, 2017-10-09 06:47
(Reply to #2)
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

Thanks for your prompt reply. The daughter board I have is with DA14585 rev AB silicon. The SDK 6.0.4 cannot be used for this version as stated in the queryhttps://support.dialog-semiconductor.com/forums/post/dialog-smartbond-bl.... Please suggest an alternative solution.

我也试着用刺激test.exe众多ion available in the location E:\Dialog\DA14585\SDK\DA14585_SDK_6.0.2.243_0\DA14585_SDK\6.0.2.243\binaries\host\windows\prod_test_cmds. While trying to execute the CLI command prodtest -p 14 unmodulated TX 2404 [UNMODULATED TX], the status code 9, SC_RX_TIMEOUT is getting returned. Please suggest the possible reasons for this too.

Thanks and regards
Wisilica

Mon, 2017-10-09 08:58
STS_Dialog
Offline
Last seen:3 years 2 months ago
Joined:2017-06-06 09:26
Hi,

Hi,

There will be free of charge replacement of your daughterboard.

Thanks,

STS_Dialog.

Accepted answer
Mon, 2017-10-09 10:01
(Reply to #4)
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

Thank you for the reply. So, there is no way we could send an unmodulated carrier wave using this version of DA14585 daughter board using SDK 6.0.2 ?

Thanks
Wisilica

Mon, 2017-10-09 10:05
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

Could you please tell the procedure for the replacement of the DA 14585 daughter board ?

Thanks
Wisilica

Mon, 2017-10-09 10:15
(Reply to #6)
STS_Dialog
Offline
Last seen:3 years 2 months ago
Joined:2017-06-06 09:26
Hi,

Hi,

I sent a mail to provide me with the necessary information. Please check it.

Thanks,

STS_Dialog.

Mon, 2017-10-09 10:28
(Reply to #7)
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

Could you please send the mail to my alternate mail ID given below :

dvenugopal@wisilica.com

Thanks
Wisilica

Mon, 2017-10-09 11:23
(Reply to #8)
STS_Dialog
Offline
Last seen:3 years 2 months ago
Joined:2017-06-06 09:26
Please it's necessary the

Please it's necessary the mail address to be the same as the register mail. Update it if it's possible.

Thanks,

STS_Dialog.

Mon, 2017-10-09 12:16
(Reply to #9)
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

Sure, will update soon.

Thanks
Wisilica

Wed, 2017-10-11 10:03
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

By when will the replacement be made ?

Thanks
Wisilica

Wed, 2017-10-11 10:07
(Reply to #11)
STS_Dialog
Offline
Last seen:3 years 2 months ago
Joined:2017-06-06 09:26
The products have already

The products have already bees sent, so it's depends on the post.

BR,

STS_Dialog.

Thu, 2017-10-12 14:44
wisilica
Offline
Last seen:7 months 4 days ago
Joined:2015-03-17 08:16
Hi,

Hi,

We have received the new set of boards. Thank you very much. Now, by executing the prod_test code in the board, and while sending unmodulated carrier wave using the prod_test.exe tool, we were able to send the carrier in 3 frequencies - 2402, 2426, 2480 Mhz. These waves were analysed using spectrum analyser by direct coupling method. The images of the spectrum analyser output are attached herewith. We are observing discrepancies in the output TX power. Instead of having the max TX power at 0dBm, the spectrum analyser output shows variation from - 1.4 to - 2.5 dBm. We have also observed that, the TX power in all the 3 channels are different.
Kindly look into this, and suggest the reasons for the same.

Thanks
Wisilica

Attachment:
Package iconDA14585 - carrier wave spectrum analysis(directly coupled).zip
Fri, 2017-10-13 16:15
(Reply to #13)
MT_dialog
Offline
Last seen:1 week 3 days ago
Staff
Joined:2015-06-08 11:34
Hi wisilica,

Hi wisilica,

Please check your other post regarding that question:

https://support.dialog-semiconductor.com/forums/post/dialog-smartbond-bl....

Thanks MT_dialog