DUT_PDLL_XTAL_TRIM_FREQ_CAL_NOT_CONNECTED

When trying to write in PLT, the following error occurs.

dut_pdll_xtal_trim_freq_cal_not_connected |FAIL | XTAL trim could not be performed. Could not detect external input frequency. Current device status = [34].

What can be considered as a cause?

电路：电路应与DA14580DEVKT-B +加速度传感器+外部SPI闪光灯相同
XTAL Trim: enable
GPIO input pulse pin: P0_3 (shared with UART RX)
Externally output pins: VBAT 3, GND, P0_2 (TX), P0_3 (RX), VPP, SW_CLK, SW_DIO

When disabling XTAL Trim, all processing succeeded.
Also, in the case of DA14580DEVKT-P + DA 14580ATDB + Accelerometer + External SPI Flash configuration, it was successful even if XTAL Trim was enabled.

PLTで書き込みを行おうとすると、次のようなエラーが発生します。

dut_pdll_xtal_trim_freq_cal_not_connected |FAIL |XTAL trim could not be performed. Could not detect external input frequency. Current device status=[34].

原因原因として何がが考えますますます

回路: DA14580DEVKT-B と同じはずの回路 + 加速度センサ + External SPI Flash
XTAL Trim: enable
GPIO input pulse pin: P0_3 (UART RX と共用)
外部に出したpin: VBAT3, GND, P0_2(TX), P0_3(RX), VPP, SW_CLK, SW_DIO

XTAL Trim を disable にすると、すべての処理が成功しました。
また、DA14580DEVKT-P + DA14580ATDB + 加速度センサ + External SPI Flash の構成の場合、XTAL Trimをenableにしても成功しました。

error log
---
软件：DA1458X / DA1468x生产线
Software version: v_3.172.2.30
PLTD DLL version: v_3.172.2.30
PDLL Version: v_3.172.2.30
UDLL Version:
生产测试BLE固件版本：v_5.0.4
Production test APP firmware version: v_5.0.4
Flash程序员固件版本：
Date: 2017-03-15
Start Time: 20:07:52.373
End Time: 20:08:03.702
Station ID: Test_station_1
Device ID: 1
COM port: 51
BD address: 11:20:30:40:50:84

| | | |
##########################################################################################################################
| 20：07：55.704 | dut_com_port_identify_started |开始| COM端口识别启动。dut = [1]。
| 20:07:58.288 |DUT_COM_PORT_IDENTIFY_OK | PASS |COM port identified OK. DUT=[1] <--> COM_PORT=[51].
| 20:07:58.366 |DUT_UDLL_FW_DOWNLOAD_INIT | STARTED |UDLL firmware download initialized. Firmware is=[C:\Users\sago\Flickpop\PLTv4\executables\binaries\prod_test_580.bin].
| 20：07：58.391 | dut_udll_fw_download_start |启动| UDLL固件下载已启动OK。固件是= [C：\ Users \ Sago \ flickpop \ pltv4 \可执行文件\ binaries \ prod_test_580.bin]。
| 20:08:00.595 |DUT_UDLL_FW_DOWNLOAD_OK | PASS |UDLL firmware downloaded OK. Firmware is=[C:\Users\sago\Flickpop\PLTv4\executables\binaries\prod_test_580.bin].
| 20：08：00.596 | DUT_UDLL_FW_DOWNLOAD_OK |通行证| UDLL固件下载OK。固件是= [C：\ Users \ Sago \ flickpop \ pltv4 \可执行文件\ binaries \ prod_test_580.bin]。
| 20:08:00.708 |DUT_PDLL_COM_PORT_INIT | STARTED |Device pdll COM port open initialized.
| 20：08：00.710 | DUT_PDLL_COM_PORT_START |启动|设备PDLL COM端口打开开始。
| 20:08:00.744 |DUT_PDLL_COM_PORT_OK | PASS |Device pdll COM port opened OK.
| 20:08:00.795 |DUT_PDLL_FW_VERSION_GET_START | STARTED |Device pdll Firmware version get started.
| 20:08:00.819 |DUT_PDLL_FW_VERSION_GET_OK | PASS |Device pdll Firmware version get OK. PDLL version=[v_3.172.2.30], BLE FW version=[v_5.0.4], APP FW version=[v_5.0.4].
| 20：08：00.821 | DUT_PDLL_XTAL_TRIM_INIT |启动| XTAL Trim操作初始化。
| 20:08:00.823 |DUT_PDLL_XTAL_TRIM_START | STARTED |XTAL trim operation started.
| 20:08:03.174 |DUT_PDLL_XTAL_TRIM_FREQ_CAL_NOT_CONNECTED | FAIL |XTAL trim could not be performed. Could not detect external input frequency. Current device status=[34].
| 20:08:03.175 |DUT_INTERNAL_SYSTEM_ERROR | ERROR |Internal system error. Current device status=[34].