你好，我正在搜索帖子和对话框：
"You dont need any extra cable or a Jtag since you have the interface board, the board has a debugger, you just plug in the USB cable turn it on and you should be able to step and run the IoT
与keil的fw，你不需要额外的东西。您在图片中指示的接口是另一个接口，以便使用不同的JTAG连接插头编程参考设计。“
一世have the interface board/IOT sensor combo. I have tried downloading the code through smart snippets but was not successful then I noticed this post. I would like to use the debugger
这里提到的，但是当我启动Keil并编译IOT项目并尝试打开调试器时，我收到错误：没有找到Cortex-M设备。我的keil与DA14580开发套件合作。有任何想法吗？谢谢你。克雷格
Device:
嗨克雷格，
伴随着物联网传感器的接口板is the one indicated in the UM-B-063 sensor development kit documentation in figure 5. Please open keil and choose the options for target, go to the debug tab and click settings, there you should see the SN of the JTAG (make sure that the port is set to SW and not JTAG). The problem is, if the 583 has firmware inside the internal flash and the fw implements sleep, the JTAG wont be able to attach to your processor. So if you dont see under the SW Device text box your processor, hit the ok or cancel button to go back in the Debug tab, hit the reset on the the interface board and click again the settings options before the 583 goes to sleep, in order to make sure that keil is able to communicate with your processor. Now in order to program the via keil before hitting the debug button on keil, hit the reset button on the interface board and hit the debug button from keil within approximatelly 2 seconds. I remind you that the above are necessary because the fw implements sleep and the debugger can't attach to the 580. You can remove the fw that is programmed into the flash by using smart snippets and the connect via JTAG, hit the flash option, hit connect, and then erase, that way you dont have to hit the reset button every time you want to program your board.
谢谢mt_dialog.
谢谢你的详细回复。这将有助于一些将遇到这个问题的人。至于我，我仍然与我当前的董事会有烦恼，我无法用智能片段编程或通过keil编程它 - 我相信它是板本身，所以我从Mouser中派出一个新的一个，如果
我遇到了任何问题。非常感谢。克雷格
你好，
“物联网传感器开发套件 - 9轴+温度/压力/压力/湿度”，在高频上采样所有传感器时，将绘制多少电流。
是关于当前/功耗细节的任何文档。
Regards,
Mahesh Chandana。
Hi Mahesh,
You can find the power consumtion measurements in the UM-B-063_DA145_IoT_sensor_development_kit.pdf at section 12.1 Power measurements along with the rates of the sensors that the measurement is done. Those are the available measurements that have been performed on the IoT
谢谢mt_dialog.
你好，我有困难programming my new boards. The boards were just manufactured and have the same pinouts/pin connects for programming
(including the 10 pin header) as your DA14583 IOT board. I cannot program them using either UART/SPI mode or JTAG mode. My existing
IOT传感器从对话程序中的两种模式都精细。我想我真的需要支持，因为这些板很昂贵
制作，似乎有一个硬件问题。从智能片段获得以下错误：我正在寻找
在这一点调试它们的策略。谢谢你。克雷格
JTAG模式：
[INFO @16-12-25 14:00:27] Header records have been removed from hex file wrbl_sfl_583.hex.
[INFO @16-12-25 14:00:27] Read 32688 bytes from file wrbl_sfl_583.hex.
[info @ 16-12-25 14:00:28]核心是锁定的，试图禁用WDT。
[警告@ 16-12-25 14:00:29]无法设置s_reset_st
[警告@ 16-12-25 14:00:29] CPU重置后没有停止。
[警告@ 16-12-25 14:00:29] CPU无法停止
[INFO @16-12-25 14:00:29] Core did not halt after reset, trying to disable WDT.
[警告@ 16-12-25 14:00:29] CPU重置后没有停止。
[警告@ 16-12-25 14:00:29] CPU无法停止
[警告@ 16-12-25 14:00:29]无法设置s_reset_st
[信息@ 16-12-25 14:00:29] Sysresetreq已经混淆了核心。尝试重新连接和使用VectreetEt。
[WARNING @16-12-25 14:00:30] Failed to reset CPU. VECTRESET has confused core.
[警告@ 16-12-25 14:00:30] CPU重置后没有停止。
[WARNING @16-12-25 14:00:30] CPU could not be halted
[信息@ 16-12-25 14:00:30]核心重置后没有停止，尝试禁用WDT。
[警告@ 16-12-25 14:00:30] CPU重置后没有停止。
[WARNING @16-12-25 14:00:30] CPU could not be halted
[WARNING @16-12-25 14:00:30] Could not set S_RESET_ST
[ERROR @16-12-25 14:00:30] Failed writing value A7 at address 50000012.
[INFO @16-12-25 14:00:30] Failed downloading firmware file to the board.
[INFO @16-12-25 14:00:30] Failed configuring SPI Flash ports and pins.
UART/SPI Mode:
[信息@ 16-12-25 14:55:30]报头记录已从十六进制文件WRBL_SFL_583.HEX中删除。
[INFO @16-12-25 14:55:30] Read 32688 bytes from file wrbl_sfl_583.hex.
[信息@ 16-12-25 14:55:35]将固件文件下载到电路板上。
[INFO @16-12-25 14:55:35] Failed configuring SPI Flash ports and pins.
[信息@ 16-12-25 14:55:44]将固件文件下载到电路板上。
[INFO @16-12-25 14:55:44] Failed configuring SPI Flash ports and pins.
[INFO @16-12-25 14:55:57] Failed downloading firmware file to the board.
[信息@ 16-12-25 14:55:57]配置SPI闪存端口和引脚。
[INFO @16-12-25 14:56:13] Failed downloading firmware file to the board.
[信息@ 16-12-25 14:56:13]配置SPI闪存端口和引脚失败。
[INFO @16-12-25 14:56:17] Failed downloading firmware file to the board.
[INFO @16-12-25 14:56:17] Failed configuring SPI Flash ports and pins.
[信息@ 16-12-25 14:56:28]将固件文件下载到电路板上失败。
[信息@ 16-12-25 14:56:28]配置SPI闪存端口和引脚。
嗨克雷格，
Regarding to the flash programming, please check the SPI flash pin configuration in Board Setup to match DA14583 pin assigement and use UART mode instead of UART/SPI mode when there is no function of current measurement. Smartsnippets usually ask users to press reset button in UART mode in order to download a flash_programmer.bin before programming a flash image, but I dont see it in the console you provided. So there might some incorrect steps in your setup. Please also confirm both of the UART and JLink driver are installed correctly.
Flash download is not supported in Keil. Please use "debug" and download the image to RAM.
Thanks Morris
谢谢你的帮助。一世realized I am missing the central solder pad for the 40VFQFN processor. Routed
垫下面的一些线条。我认为这是问题。我看了数据表，没有太多
提到中央垫，我没有意识到这需要这是我第一次使用这个芯片
格式。
For the sake of my fix where I have to be a bit creative in dealing with the central ground pad, I need to know (and couldn't
find in the datasheet), if pin 16 (DA14583 GND pin 16) is connected internally to the central ground pad? If not, can I get away with not grounding
that central ground pad or is that an absolute necessity? Thank you in advance. Craig
嗨克雷格，
销16是DCDC接地，并且未连接到作为中心接地焊盘的基板接地。所以有必要有接地垫连接。评估板的布局可以为您提供良好的参考。
Thanks Morris